Everyone will have their own way of thinking on the subject of Tools You Need to Install a New Bathtub .
Mounting a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old tub with a brand-new one is also a reasonably challenging job. If the old tub is easily obtainable, the task can move rapidly; if you need to open up a wall to get rid of the old tub as well as position the brand-new bathtub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will need an assistant to vacate the old tub and set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is better to consider using one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you set up a new bathtub in your restroom if you have actually currently purchased a new tub as well as do not require to transform the setup of your previous water system pipelines.
Your tools as well as material checklist should make up the following:
Getting ready for the Installation
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to stop stress on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of getting rid of the existing taps can be quite troublesome because of the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, place the bathtub in the needed position. The wood boards are useful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub till the level reviews degree.
To install taps, fit all-time low of the furthest flexible faucet port to the ideal supply pipeline by making a compression join; then do the same for the various other faucet.
Switch on the supply of water and examine all joints as well as new pipework for leakages and tighten them if required. Load the tub as well as additionally check the overflow electrical outlet and the normal outlet for leaks.
Lastly, deal with the bath paneling as defined in the maker's user's manual. Tiling and also sealing around the bathtub must wait until the bathtub has actually been used a minimum of once as this will certainly settle it into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin guaranteeing that the washers are in place in between the tap and the sink. Secure the tap in place with the maker given backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, leading to problems with dampness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to permit the movement experienced when the bathtub remains in usage. The sealant can fracture rather early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on How to Install a Bathtub? Place a review further down. We will be interested to find out your insights about this blog entry. Hoping that you come back again in the future. Be sure to take the time to distribute this blog if you liked it. Thank you for your time. Kindly check our site back soon.
Apply Now